![centos hp cciss centos hp cciss](https://image.slidesharecdn.com/hpandlinux-151005231121-lva1-app6892/95/hp-and-linux-2-638.jpg)
#Centos hp cciss install
(Its a twin 2.8GHz Xeon) The CentOS install put the cciss driver on, and all works fine. The server has a SmartArray 5i with two 73GB 15k drives in a Raid 1 configuration. Will post link below, as I have seen other threads looking for SP73052.exe.
#Centos hp cciss update
By some miracle, I found the BIOS update for this model, bringing the version to 2015. I have a two EOL HP units, HP Proliant D元60 G5, that I have been fiddling around with to install CentOS/RHEL 7 on. Physicaldrive 1I:2:2 (port 1I:box 2:bay 2, SAS, 900. I've got a D元60G3 running CentOS 5, patched to a fairly current level. CentOS/RHEL 7 Installation w/ CCISS Driver.
#Centos hp cciss upgrade
Neither direct install nor upgrade install from Centos 6.6 will work. My thread on the centos 7 forum describes my journey. The short of the matter is that Centos 7 does not support some HP CCISS RAID controllers.
#Centos hp cciss drivers
The latter failed as there are no cciss drivers included for the. Physicaldrive 1I:2:1 (port 1I:box 2:bay 1, SAS, 900.1 GB, OK) I spent the last 8 hours trying to get Centos 7 to install on a ProLiant BL460c with a QLogic 2432 SAN card. I managed to install CentOS 6.7, after first trying 7 (1511), on my HP Proliant D元80 G3. Internal Drive Cage at Port 2I, Box 0, OK Internal Drive Cage at Port 1I, Box 2, OK These are used extensively by the HP Array Configuration Utility, SNMP storage agents, and so on. But a component of the HP set of tools is the hpssacli or hpacucli utility, whose output could be parsed: # hpssacli ctrl all show config CCISSGETDRIVVER Returns driver version in three bytes encoded as: (majorversion << 16) (minorversion << 8) (subminorversion) CCISSPASSTHRU, CCISSBIGPASSTHRU Allows 'BMIC' and 'CISS' commands to be passed through to the Smart Array. If you absolutely must have this reported in Nagios, it seems like there are plenty of options. Those can email, dump to syslog and send SNMP traps. For CentOS legacy GRUB SuperGRUB works well.My recommendation would be to use the HP Management and Health Agents for the server. cciss is a block driver for older HP Smart Array RAID controllers. As CentOS does not use subscriptions for receiving updates, the functionality provided by virt-who has never been used in CentOS. CentOS 5.8 introduced a package virt-who, used for reporting virtual guest information to the subscription manager.
![centos hp cciss centos hp cciss](https://i0.wp.com/www.geeklingo.net/wp-content/uploads/2017/08/VMM-Installing-CentOS.jpg)
Super Grub Disk has a variety of open source boot recovery tools. The HP cciss RAID driver has been updated to the latest version. If you wish to re-install GRUB to the MBR on a HP Smart Array disk (/dev/c0d0): # grub-install /dev/cciss/c0d0Īlternative Recovery from GRUB Issues – Super Grub Disk.If you wish to re-install GRUB to the MBR on an IDE disk (/dev/hda):.If you wish to re-install GRUB to the PBR of Partition #2 on a SCSI or SATA disk (/dev/sda2):.If you wish to re-install GRUB to the MBR on a SCSI or SATA disk (/dev/sda):.Change root to real root (‘/’) on your hard disk: # chroot /mnt/sysimage.Mount all filesystems in read-write mode.Type «linux rescue» at the «boot:» prompt.Boot from CentOS installation disc (for example, CD #1 or DVD).It should be largely fine for CentOS 5 Continue reading 'Monitoring HP ProLiant D元60 hardware in CentOS, with. If you have repaired your system from a backup tape (by dump or tar for example), or have installed another OS such as one from Redmond that may have overwritten the master boot record (MBR), you will need to repair the bootstrap area. My original post for monitoring HP storage hardware in CentOS is now out of date, so I decided to write an updated post for monitoring all hardware, not just storage hardware, and for optionally including this hardware monitoring in Nagios.